地下商场空调设计问题的探讨

本文分析了地下商场的特征 ,并相应提出了地下商场通风空调设计的有关数据、方法及注意事项     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

轻型钢骨结构低层住宅设计荷载分析

本文讨论了北美低层钢骨结构住宅结构设计的荷载问题，包括各类荷载的取值和计算方法，以及荷载组合模式，并提出了在我国相关规范没有出台前，在国内进行设计时应该注意的一些问题。     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

电力负荷削峰减载系统在珠钢电炉的应用

借助现场采集装置,在计算机上获取每一分钟的冶炼工艺电能需求量,显示当前15分钟时段已发生的电耗量,调整用户设定,实现需量自动刷新、报警和专家分析推荐后续用量;实现平稳用电并减少对电网冲击,同时降低电能最大需用量以减少成本。     

Total simulation model of the thermo-mechanical process in shape rolling of steel rods

The production of steel reinforcing bars for civil engineering is investigated by means of FEM-simulation. An integrated system for computing appropriate thermo-mechanical parameters of the rolling process is proposed. Generalized plane strain approach and coupled thermal-mechanical solution are applied. The microstructural model combines both the effect of the recrystallization mechanisms (static, dynamic and metadynamic) upon the austenite grain forming in hot rolling and that of phase transformation upon the final microstructure. The phases are created during interrupted below the temperature of martensite transition cooling. Thus a typical industrial process for thermo-mechanical strengthening of reinforcing bars, known as Tempcor-process is considered. Computational results are validated to experimental measured mechanical properties of the steel. By means of computer simulation the system can perform different solutions, giving the possibility to obtain a reasonable choice of different thermo-mechanical rolling conditions.     

炼铁生产环境负荷分析和预测研究

利用寿命周期评价的思想，计算了炼铁生产过程中的环境负荷，并分析了各因素对环境负荷的影响，运用神经网络对炼铁生产过程环境负荷进行了预测。     

轧制力测量装置的使用与维护

简要论述了轧制力测量的基本原理，并从实际经验出发深入探讨了测压头的维护与管理要点。